WHY YOUR ORBY GUN IS LOSING POWER?
If your gel blaster suddenly feels underpowered, fires inconsistently, or doesn’t shoot at all — don’t worry. Power loss is a common problem, and most of the time, it’s quick to diagnose and fix.
Whether you use a sniper gel blaster, an orby gun Glock, or a Briliantz model, here are the key reasons your blaster might be struggling — and how to bring back full performance.
1. Weak or drained battery
One of the most frequent causes of poor power is a tired or undercharged battery.
How to identify battery problems
- The blaster fires weakly or stops during bursts
- It doesn’t cycle properly
- It works only for a short time
What to do:
- Charge the battery fully using the correct charger
- Avoid using swollen or old batteries — replace them
- Use 7.4V or 11.1V LiPo (if your blaster is compatible)
- Store LiPo batteries at 50–60% charge when not in use
2. Blocked or dirty barrel
Debris or gel residue can build up inside your barrel, lowering pressure and accuracy.
How to clean it
- Remove the magazine and battery
- Use a cleaning rod and cloth to gently push through the barrel
- Blow compressed air through to remove leftover residue
A clean barrel increases both shooting power and accuracy.
3. Gel ball hydration problems
Badly prepared gel balls can significantly reduce your blaster’s power.
Hydration tips
- Soak gel balls for 3–4 hours as recommended
- Ensure they are fully expanded (typically 7–8mm)
- Discard broken or overgrown gel balls
Properly hydrated gels give better pressure and performance.
4. Worn gearbox or internals
Like any mechanical system, gel blaster parts can wear over time.
What to look for
- Clicking or grinding noises
- Power drop despite a good battery
How to fix it:
- Inspect the gearbox, piston, and spring
- Replace worn components
- Lubricate moving parts with silicone grease
Keeping internals in top shape will ensure consistent power.
5. Air seal issues
Leaks inside the cylinder or barrel reduce air pressure.
How to spot and fix them
- Look for sudden FPS drops
- Listen for air escaping
Check and replace:
- O-rings (dry or cracked)
- Cylinder head and nozzle seals
- Apply silicone lube
- Tighten the barrel and cylinder assembly
Improved air seal = better shooting power.
6. Motor alignment or failure
If your motor is misaligned, power won't transfer correctly.
How to check motor alignment
- The blaster hums but doesn’t fire
- Motor heats up or smells burnt
Fix it by:
- Removing the grip plate
- Adjusting the motor screws
- Replacing burnt-out motors
Proper alignment ensures reliable cycling.
7. Overheating during play
Heat buildup during long sessions can cause temporary power drops.
Prevention tips
- Don’t fire continuously for too long
- Allow rest time between rounds
- Keep a backup battery to swap out
Heat can reduce battery efficiency and damage components over time.
8. Low-quality gel balls
Cheap ammo is inconsistent and affects performance.
Choose reliable brands
Use gels like:
- Briliantz
- Ultra Elite
- Milky White
These are uniform in size and reduce the risk of jams or pressure loss.
9. Loose or faulty wiring
A poor electrical connection can cut off power intermittently.
Where to check
- Wires near the battery, motor, or trigger
- Loose or broken connectors
- Frayed insulation
Secure or replace any damaged wires to restore power flow.
10. Environmental conditions
Weather can affect battery and gel performance.
Storage and play tips
- Avoid leaving gels or batteries in cold or hot environments
- Keep ammo and gear in a cool, dry place
- Don’t expose batteries to direct sunlight or freezing temperatures
Temperature can weaken pressure and power.
Bonus tip – upgrade smart
Once your blaster is running smoothly, consider upgrades — but do it wisely.
Upgrade advice
- Swap one component at a time (spring, hop-up, barrel)
- Stick to trusted brands like Briliantz
- Avoid untested or cheap mods — they often reduce reliability
FAQ – restoring gel blaster power
Why is my blaster weak even after charging the battery?
Most likely, there’s a poor air seal or the battery is underperforming.
Can cheap gel balls damage my gearbox?
Yes — if they’re inconsistent in size or improperly hydrated, they can cause jams and internal wear.
How often should I maintain my blaster?
Clean after each game and do a full check every few months.
Should I oil internal parts?
Yes, but only use silicone lubricant — never petroleum-based oils.
Conclusion
Most gel blaster power issues are caused by small, easily fixable problems — like dirty barrels, weak batteries, or poor gel hydration. With proper care, high-quality gel balls, and regular maintenance, you can keep your blaster performing at full strength.
Stick with trusted models like the Briliantz range or RPK gel blasters, known for strong, reliable shooting. Take care of your gear, and it’ll take care of your game.